Tuning For Sub-10 Seconds Failover Time in Overlapping Networks

Introduction

The purpose of this document is to provide the instructions for tuning network configurations for sub-10 seconds failover time when network address ranges on-prem and cloud are overlapping.

The scenario is described in the following diagram.

s2c overlapping cidr topology

In the above diagram, Client-1 and Client-2 need to communicate with on-prem network. However, both Client-1 and Client-2 network address ranges overlap with each other, and worse yet, they both overlap with on-prem network address range (10.0.0.0/16). Such scenarios happen when Client-1, Client-2 and the on-prem networks belong to three different organizations.

The traditional solution is to build IPSEC tunnel between the two networks and use SNAT/DNAT rules to translate each addresses, as demonstrated in this example. Such solution requires a potentially large number of SNAT/DNAT rules which is difficult to configure and maintain.

With the introduction of Mapped Site2Cloud for address overlapping networks, you no longer need to wrestle with the individual SNAT/DNAT rules.

Configuration Steps

This example uses Aviatrix Gateway on client site to simulate fast convergence environment

Step 1: Follow the Multicloud Transit workflow to launch gateways

Log in to the Controller console, go to Multi-CLOUD TRANSIT. Follow step 1, step 4 and step 6 respectively to launch transit and spoke gateways, and attach spoke gateways to transit.

Create VPN tunnel between Transit Gateway and On-prem.

Step 2: Create a Site2Cloud tunnel between Spoke Gateway and Client-1

2.1 Configure S2C from Spoke Gateway to Client-1

Go to Controller Console → Site2Cloud → Setup.

Click "+Add New". Fill the form and click OK. Select "Mapped" for the Connection Type field.

Field Value

VPC ID/VNet Name

Choose VPC ID (Select Spoke Gateway VPC)

Connection Type

Mapped

Connection Name

Arbitrary (e.g. S2C-SPK-to-Client1)

Remote Gateway Type

Aviatrix

Tunnel Type

Route-based

Algorithms

Uncheck this box

IKEv2

Uncheck this box

Over Private Network

Uncheck this box

Enable HA

Check this box

Primary Cloud Gateway

Select the Aviatrix Gateway created above

Backup Gateway

Select the Aviatrix Gateway HA

Remote Gateway IP Address

Public IP of Client-1 Primary Gateway

Remote Gateway IP Address (Backup)

Public IP of Client-1 Backup Gateway

Pre-shared Key

Optional (auto-generated if not entered)

Same Pre-shared Key as Primary

Check this box

Custom Mapped

Uncheck this box

Remote Subnet (Real)

10.10.0.0/16 (Client-1 Real CIDR)

Remote Subnet (Virtual)

100.64.0.0/16 (Client-1 Virtual CIDR)

Local Subnet (Real)

10.10.0.0/16 (On-Prem Network CIDR)

Local Subnet (Virtual)

192.168.0.0/16 (On-Prem Virtual CIDR)

2.2 Configure S2C from Client Side

Go to Controller Console → Site2Cloud → Setup.

Click "+Add New". Fill the form and click OK. Select "unmapped" for the Connection Type field.

Field Value

VPC ID/VNet Name

Choose VPC ID (Select Client-1 VPC)

Connection Type

Unmapped

Connection Name

Arbitrary (e.g. S2C-Client1-to-SPK-GW)

Remote Gateway Type

Aviatrix

Tunnel Type

Route-based

Algorithms

Uncheck this box

IKEv2

Uncheck this box

Over Private Network

Uncheck this box

Enable HA

Check this box

Primary Cloud Gateway

Select the Aviatrix Gateway created above

Backup Gateway

Select the Aviatrix Gateway HA

Remote Gateway IP Address

Public IP of Spoke Primary Gateway

Remote Gateway IP Address (Backup)

Public IP of Spoke Backup Gateway

Pre-shared Key

Optional (auto-generated if not entered)

Same Pre-shared Key as Primary

Check this box

Remote Subnet

192.168.0.0/16 (On-Prem Virtual CIDR)

Local Subnet

10.10.0.0/16 (Client-1 Local Network CIDR)

Step 3: Configure global parameters

Go to Controller Console → Settings → Advanced

  1. Click on "Tunnel" tab and change "Status Change Detection Time" and save settings.

Field Value

Aviatrix Entity

Choose Controller

Detection time (secs)

20

  1. Click on "Keepalive" tab and modify Keepalive Template Configuration

Field Value

Keep Alive Speed

fast

Step 4: Configure site2cloud parameters

Go to Aviatrix Controller’s Console → Site2Cloud → Setup.

4.1 Spoke Gateway Side

Select Spoke Gateway VPC, spoke gateway to client site2cloud connection and click "Edit"

  1. Make sure only one tunnel is UP and HA status Active-Standby

  2. DPD Timer is enabled, configure DPD timers as shown below and click "Save and Apply".

Field Value

Initial Delay

1

Retry

1

Maxfail

1

  1. Forward Traffic to Transit Gateway is enabled

  2. Event Triggered HA is enabled

4.2 Client Side

Select Client VPC, client to spoke site2cloud connection and click "Edit"

  1. Make sure only one tunnel is UP and HA status Active-Standby

  2. DPD Timer is enabled, configure DPD timers as shown below and click "Save and Apply".

Field Value

Initial Delay

1

Retry

1

Maxfail

1

  1. Active Active HA is disabled

  2. Event Triggered HA is enabled

Test site2cloud fast convergence

Bring down IPSec primary tunnel and measure convergence.