Ingress Protection via Aviatrix Transit FireNet with FortiGate

This document illustrates a widely deployed architecture for an Ingress traffic inspection/protection firewall that leverages AWS Load Balancers, Transit FireNet for AWS and FortiGate VM in AWS.

Ingress traffic from the Internet forwards to firewall instances first in the Aviatrix Transit FireNet VPC and then reaches application servers as shown in the diagram below. In this design pattern, each firewall instance must perform:

transit_firenet_ingress

This design pattern also supports multiple firewalls (scale out fashion) for each Aviatrix Transit FireNet gateway.

This document describes step-by-step Ingress Protection via Aviatrix Transit FireNet with a FortiGate deployment workflow:

For more information about Transit FireNet, see the following documents:

Prerequisites

Upgrade Aviatrix Controller to at least version 6.1. In this example, we are going to deploy the below VPCs in AWS:

  • Aviatrix Transit FireNet VPC (i.e. 10.70.0.0/16)

  • Aviatrix Spoke VPC for Application (i.e. 10.3.0.0/16)

Workflow on Transit FireNet for AWS

Refer to Creating a VPC using CoPilot for steps on how to:

  • Deploy a Transit VPC

  • Deploy a Spoke VPC for Application (can also be done in the AWS portal). You can also use an existing VPC.

Adjust the topology depending on your requirements.

Launch and Associate Firewall Instance

  1. Subscribe to Firewall Vendor in AWS Marketplace for FortiGate Next Generation Firewall.

  2. Launch a FortiGate Firewall instance for each Aviatrix Transit FireNet gateway.

    Example setting Example value

    Firewall Image

    Fortinet FortiGate Next-Generation Firewall

    Firewall Image Version

    6.4.2

    Firewall Instance Size

    c5.xlarge

    Egress Interface Subnet

    Select the subnet whose name contains "FW-ingress-egress".

    Key Pair Name (Optional)

    The .pem file name for SSH access to the firewall instance.

    Attach

    Check

  3. Wait for a couple of minutes for the FortiGate Firewall instances to change to Running Instance state.

A later section will describe how to set up basic configuration for FortiGate (Fortinet) in Workflow on Firewall Instances - FortiGate.

Workflow on AWS Application Load Balancer

This workflow example describes how to:

  • Place an internet-facing AWS Load Balancer to load balance traffic to firewall instances in Transit FireNet.

  • Place an internal AWS Load Balancer to load balance traffic to a private application server in Application Spoke.

  • Set up the related network components and private application web server with HTTP and port 8080.

Adjust the settings depending on your requirements.

Create an AWS Application Load Balancer with Internet-Facing Scheme

In your AWS Management Console, in the Transit FireNet VPC, create an internet-facing AWS Application Load Balancer by following the steps below:

  1. Select Application Load Balancer HTTP/HTTPS.

    Ingress_ALB

  1. Select items as follows:

    Section Field Value

    Basic Configuration

    Scheme

    internet-facing

    IP address type

    ipv4

    Listeners

    Load Balancer Protocol

    HTTP

    Load Balancer Port

    8080

    Availability Zones

    VPC

    Aviatrix Transit FireNet VPC

    Availability Zones

    select the subnet with -Public-FW-ingress-egress-AZ- in each AZ

Ingress_Internet_ALB_Step_1_Configure_Load_Balancer

  1. Create a security group with Protocol TCP and Port 8080.

    Ingress_Internet_ALB_Step_3_Configure_Security_Groups

  2. Select items as follows:

    Section

    Field

    Value

    Target group

    Target group

    New target group

    Target type

    Instance

    Protocol

    HTTP

    Port

    8080

    Health checks

    Protocol

    HTTPS

    Path

    /

    Advanced health check settings

    Port

    override with 443

    Success codes

    302

Ingress_Internet_ALB_Step_4_Configure_Routing

  1. Select firewall instances and click the button "Add to registered" in Step 5: Register Targets.

    Ingress_Internet_ALB_Step_5_Register_Targets_1

  2. Confirm the selected firewall instances are placed under the section "Registered targets".

    Ingress_Internet_ALB_Step_5_Register_Targets_2

  3. Review the configuration from the previous step.

    Ingress_Internet_ALB_Step_6_Review

  4. Wait for a couple of minutes and check firewall instances' healthy Status behind AWS Application Load Balancer.

    Internet_ALB_WEB_HTTP_8080_tg_healthcheck

Healthy status targets behind the AWS load balancer can be found on the page EC2  Target groups  selecting the target group  Targets in the AWS Console.

Launch an Apache2 Web server in Application Spoke

In the Application Spoke, create a virtual machine and install Apache2 HTTP Server with custom port 8080 as a web application server.

Example setting

Example value

Protocol

HTTP

Port

8080

Refer to Install The Latest Apache2 HTTP Server ( 2.4.34 ) On other opensource OS Servers to install Apache2 HTTP Server.

Refer to How To Change Apache Default Port To A Custom Port to use custom port 8080.

Create an AWS Application Load Balancer with Internal Scheme

In the AWS Management Console in the Application Spoke VPC, create an internal AWS Application Load Balancer:

  1. Select Application Load Balancer HTTP/HTTPS.

    Ingress_ALB

  2. Select items as follows in Step 1: Configure Load Balancer.

    Section Field Value

    Basic Configuration

    Scheme

    internal

    IP address type

    ipv4

    Listeners

    Load Balancer Protocol

    HTTP

    Load Balancer Port

    8080

    Availability Zones

    VPC

    Aviatrix Spoke VPC for application

    Availability Zones

    select the subnet where private application servers locate

Ingress_Internal_ALB_Step_1_Configure_Load_Balancer

  1. Create a security group with Protocol TCP and Port 8080 in Step 3: Configure Security Groups.

  2. Select items as follows in Step 4: Configure Routing.

    Section

    Field

    Value

    Target group

    Target group

    New target group

    Target type

    Instance

    Protocol

    HTTP

    Port

    8080

    Health checks

    Protocol

    HTTP

    Path

    /

    Advanced health check settings

    Port

    traffic port

    Success codes

    200

  3. Select private application server and click the button "Add to registered" in Step 5: Register Targets

  4. Review the configuration in Step 6: Review.

    Ingress_Internal_ALB_Step_6_Review

Workflow on Firewall Instances - FortiGate

This is just a simple example to set up a firewall for Ingress traffic. Adjust the security settings depending on your requirements.

Set up Basic Configuration for FortiGate (Fortinet)

Configure Destination NAT (DNAT) to the FQDN/IP of Internal Application Load Balancer

  1. Log in to the FortiGate GUI.

  2. Navigate to the page Policy & Objects > Virtual IPs.

  3. Click Create New.

  4. Enter fields for Name, Comments, Interface, Type, External IP address, Mapped address, and Port Forwarding as follows:

    Section

    Example setting

    Example value

    Edit Virtual IP

    VIP type

    IPv4

    Name

    DNAT-to-Internal-ALB-WEB-HTTP-8080

    Comments

    DNAT-to-Internal-ALB-WEB-HTTP-8080

    Network

    Interface

    WAN (port1)

    Type

    FQDN

    External IP address

    Private IP of interface WAN (port1)

    Mapped address

    Create a new tag 'Internal-ALB-WEB-HTTP-8080'

    Port Forwarding

    Status

    enable

    Protocol

    TCP

    External service port

    8080

    Map to port

    8080

Ingress_Fortigate_DNAT

  1. Create a tag for Mapped address by clicking + Create.

Ingress_Fortigate_DNAT_Mapped_address

  1. Enter fields for Name, Type, FQDN, and Interface for Mapped address as follows:

    Example setting Example value

    Name

    Internal-ALB-WEB-HTTP-8080

    Type

    FQDN

    FQDN

    DNS name of the internal AWS Application Load Balancer which is created in the previous step

    Interface

    any

Ingress_Fortigate_DNAT_Mapped_address_2

FQDN is the DNS name of the 'internal' AWS Application Load Balancer not the 'internet-facing' AWS ALB.
DNS name of the AWS Application Load Balancer can be found on the page EC2  Load Balancing  Load Balancers  selecting the Load balancer  Description  DNS name

Apply Destination NAT (DNAT) and configure Source NAT (SNAT) on firewall’s LAN interface in Firewall Policy to allow Ingress traffic

  1. Navigate to the page Policy & Objects  Firewall Policy.

  2. Click +Create New.

  3. Enter fields for Name, Incoming Interface, Outgoing Interface, Source, Destination, Service, Action, NAT, IP Pool Configuration as follows:

    Section Example setting Example value

    Edit Policy

    Name

    Ingress-WEB-HTTP-8080

    Incoming Interface

    WAN (port1)

    Outgoing Interface

    LAN (port2)

    Source

    all

    Destination

    Select the Virtual IPs 'DNAT-to-Internal-ALB-WEB-HTTP-8080' which is created in the previous step

    Service

    Create a new service for HTTP-8080

    Action

    ACCEPT

    Firewall / Network Options

    NAT

    Enable

    IP Pool Configuration

    Use Outgoing Interface Address

To enable DNAT function, you must select 'Virtual IPs' for Destination under Edit Policy.

To enable SNAT function, you must enable NAT with IP Pool Configuration under Firewall / Network Options.

Ingress_Fortigate_Firewall_policy

  1. Create a new service for HTTP-8080 by clicking +Create.

    Section

    Example setting

    Example value

    New Service

    Name

    HTTP-8080

    Category

    Web Access

    Protocol Options

    Protocol Type

    TCP/UDP/SCTP

    Address

    IP Range with 0.0.0.0

    Destination Port

    TCP with port 8080

    Ingress_Fortigate_Firewall_policy_service

  1. Review the Firewall Policy.

    Ingress_Fortigate_Firewall_policy_review

  2. Repeat the above steps for all your firewall instances.

Reference Material

Ready to go

Now firewall instances and private application server are ready to receive Ingress traffic.

Open your browser and access the DNS of AWS Internet Application Load Balancer with HTTP and port 8080.

Ingress_private_WEB_server_access

Ingress Protection via Aviatrix Transit FireNet for Multiple Applications

If you have a use case where you want to inspect traffic for multiple applications using the same FW, you need to add more NAT rules on the firewall.

  1. Create an additional subnet in the security VPC (/24) for the LB.

  2. Create additional ALB/NLB based on the number of application.

  3. Add a SNAT/DNAT same as above for each application mapping it for the specific LB.