AWS Multicloud Transit BGP over LAN Workflow
Introduction
Transit BGP to LAN allows Aviatrix Transit Gateways to communicate with a pair of instances in the same VPC in AWS without running any tunneling protocol such as IPsec or GRE. One use case is to interoperate with third-party virtual appliances such as SD-WAN cloud instances that do not have the capability to support BGP over any tunneling protocols.
For example, integrating with SD-WAN gateways can be deployed as below, where an Aviatrix Multicloud Transit Gateway connects to a third-party cloud instance in the same VPC in AWS.
![sd_wan_integ_aws](_images/sd-wan-integ-aws.png)
This document describes a step-by-step instruction on how to build Aviatrix Transit Gateway to External Device using BGP over LAN in AWS. In this Tech Note, you learn the following:
-
Workflow on deploying Aviatrix Transit Solution
-
Workflow on launching third-party cloud instances
-
Workflow on building BGP over LAN
For other BGP over LAN workflows, please see the documents below:
For more information about Multicloud Transit Network and External Device, please see the documents below:
|
The key ideas for this solution are:
-
A BGP session establishes between a third-party cloud instance and Aviatrix Transit Gateway via each LAN interface in the same VPC.
-
Data plane traffic also runs between a third-party cloud instance and Aviatrix Transit Gateway via each LAN interface without a tunnel protocol such as IPsec and GRE.
Prerequisite
-
Upgrade Aviatrix Controller to at least version.
-
In this example, we are going to deploy the below VPCs in AWS:
-
Transit VPC (i.e. 10.1.0.0/16) by utilizing Aviatrix feature Create a VPC with Aviatrix FireNet VPC option enabled.
-
Spoke VPCs (i.e. 192.168.1.0/24 and 192.168.2.0/24) by utilizing Aviatrix feature Create a VPC as the previous step or manually deploying it in each cloud portal. Moreover, feel free to use your existing cloud network.
-
-
Third-party cloud instance has high throughput supported.
Deploying the Aviatrix Multicloud Transit Solution
Refer to Global Transit Network Workflow Instructions for the below steps. Please adjust the topology depending on your requirements.
-
Deploy the Aviatrix Multicloud Transit Gateway and HA with High Performance Encryption Mode enabled. In this example, size c5n.4xlarge are selected to benchmark performance.
-
Deploy a Spoke Gateway and HA to launch Aviatrix Spoke gateway and enable HA with High Performance Encryption Mode enabled in Spoke VPC. In this example, size c5n.4xlarge are selected to benchmark performance.
-
Attach Spoke Gateways to Transit Network to attach Aviatrix Spoke Gateways to Aviatrix Transit Gateways.
Launching Third-Party Cloud Instances
Deploy third-party cloud instances in the same VPC where Aviatrix Transit Gateways locate.
-
Create a third-party cloud instance and put MGMT interface in public gateway subnet.
-
Create a new public WAN subnet and a dedicated routing table for WAN interface if needed.
-
Create a new private LAN subnet and a dedicated routing table (optional) for LAN interface.
-
Make sure the function "Source/Dest check on third-party cloud instance’s interfaces is disabled.
The primary Aviatrix Transit Gateway must be deployed in the same available zone as the first third-party cloud instance. The HA Transit Gateway if deployed must reside in the same available zone as the second cloud instance. |
Building BGP over LAN
Configure BGP over LAN on the Aviatrix Transit Gateway.
-
Log in Aviatrix Controller and go to Multi-Cloud Transit > Setup > External Connection tab.
-
Select External Device > BGP > LAN.
-
Enter the following information in the fields below.
Transit VPC Name |
Select the Transit VPC ID where Transit GW was launched |
Connection Name |
Provide a unique name to identify the connection to external device |
Aviatrix Transit Gateway BGP ASN |
Configure a BGP AS number that the Transit GW will use to exchange routes with external device |
Primary Aviatrix Transit Gateway |
Select the Transit GW |
Enable Remote Gateway HA |
Check this option in this example to connect two external devices |
Remote BGP AS Number |
Configure a BGP AS number that third-party cloud primary instance will use to exchange routes with Aviatrix Transit Primary |
Remote LAN IP |
Use the private IP of the LAN interface of the third-party cloud primary instance |
Local LAN IP |
Leave it blank and the controller will assign an IP in the same subnet where the Remote LAN IP locates. Optionally configure an IP of your choosing within the same subnet where the Remote LAN IP locates. |
Remote BGP AS Number (Backup) |
Configure a BGP AS number that third-party cloud HA instance will use to exchange routes with Aviatrix Transit HA |
Remote LAN IP (Backup) |
Use the private IP of the LAN interface of the third-party cloud HA instance |
Local LAN IP (Backup) |
Leave it blank and the controller will assign an IP in the same subnet where the Remote LAN IP (Backup) locates. Optionally configure an IP of your choosing within the same subnet where the Remote LAN IP (Backup) locates. |
-
Click Connect to generate BGP session over LAN.
(Optional) Downloading the BGP over LAN configuration sample from Aviatrix Controller
-
Navigate to Site2Cloud > Setup and select the connection that you created with Connection Name in the previous step.
-
Click Edit.
-
Select Vendor type, Platform, and Software.
-
Click Download Configuration".
Configuring BGP over LAN on Third-Party Cloud Instance
-
(Optional) Open the downloaded BGP over LAN configuration file.
-
Configure those related BGP and LAN info on third-party cloud instance.
Verifying LAN status on Aviatrix Controller
-
Open your Aviatrix Controller and go to Site2Cloud > Setup.
-
Find the connection that you created with Connection Name in the previous step.
-
Check the Tunnel Status.
![aviatrix_bgp_lan_status_1](_images/bgp-lan-status-one.png)
-
Go to Multi-Cloud Transit > List.
-
Select the Transit Primary Gateway that was created in the previous step.
-
Click Details/Diag.
-
Scroll down to Connections > On-prem Connections.
-
Find the connection that you created with Connection Name in the previous step and check the Tunnel Status.
![aviatrix_bgp_lan_status_2](_images/bgp-lan-status-two.png)
Ready to Go
At this point, run connectivity and performance test to ensure everything is working correctly.