Anonymous Internet Surfing Solution Overview
Normally, when you surf an Internet website, the website administrator can easily identify where the user is located. This is done by identifying the source IP address (public IP address assigned to your location) contained in the packets. Sometimes Internet browsing for online research needs to be anonymous.
This document describes how to set up anonymous browsing from a client machine by routing Internet traffic through an AWS-based Gateway in a different region.
Configuration Workflow
Pre-Configuration Checklist
Before configuring VPC Site-to-Cloud peering, make sure the following prerequisites are completed.
Pre Configuration Check List
-
Deploy the Aviatrix Controller.
-
Create AWS VPCs and Check Settings.
These prerequisites are explained in detail below.
Deploying the Aviatrix Controller
The Aviatrix Controller must be deployed and set up prior to configuring VPC and site peering. Please refer to the Aviatrix Controller Getting Started Guide for AWS on how to deploy the Aviatrix Controller.
Check and make sure you can access the Aviatrix Controller dashboard and log in with an administrator account. The default URL for the Aviatrix Controller is:
https://<public ip of Aviatrix Controller>
Creating AWS VPCs and Checking Settings
-
Create 2 VPCs - VPC #1 (in Region 1) with CIDR 10.1.0.0/16 and VPC #2 (in Region 2) with CIDR 10.2.0.0/16
-
In VPC #1, create 2 public subnets in the same Availability Zone - 10.1.0.0/24 and 10.1.1.0/24. This means that both subnets must be associated with a route table whose default route points to IGW.
-
In VPC #2, create 1 public subnet - 10.2.0.0/24. This means that one subnet must be associated with a route table whose default route points to IGW.
Configuration Steps
Make sure the pre-configuration steps in the previous section are completed before proceeding.
The instructions in this section will use the following architecture. The CIDR and subnets may vary depending on your VPC setup; however, the general principles will be the same.
![anonymous browsing](../building-your-network/_images/anonymous-browsing.png)
Deploying Gateways
The first step is to deploy Aviatrix Gateways in each VPC.
Instructions:
-
Log in to the Aviatrix Controller.
-
Create Aviatrix Peering Gateway #1 in Subnet1 of VPC #1 (in Region 1).
-
Click on Gateway > New Gateway.
Setting | Value |
---|---|
Cloud Type |
Choose AWS. |
Gateway Name |
This name is arbitrary (e.g. vpc-01-avx-gw) |
Account Name |
Choose the account name. |
Region |
Choose the region of VPC #1. |
VPC ID |
Choose the VPC ID of VPC #1. |
Public Subnet |
Select a public subnet where the gateway will be deployed (e.g. 10.1.0.0/24). |
Gateway Size |
t2.micro is fine for testing |
Enable NAT |
Unmark this checkbox (IMPORTANT) |
VPN Access |
Unmark this checkbox |
Designated Gateway |
Unmark this checkbox |
Allocate New EIP |
Unmark this checkbox |
Save Template |
Unmark this checkbox |
-
Click OK. It will take a few minutes for the gateway to deploy. Do not proceed until the gateway is deployed.
-
Create an Aviatrix VPN Gateway in Subnet2 of VPC #1 (note that VPN Gateway is in a different subnet of Peering Gateway).
-
Click on Gateway > New Gateway.
Setting | Value |
---|---|
Cloud Type |
Choose AWS. |
Gateway Name |
This name is arbitrary (e.g. vpc-01-avx-vpn) |
Account Name |
Choose the account name. |
Region |
Choose the region of VPC #1. |
VPC ID |
Choose the VPC ID of VPC #1. |
Public Subnet |
Select the public subnet where the VPN gateway will be deployed (e.g. 10.1.1.0/24) |
Gateway Size |
t2.micro is fine for testing. |
Enable NAT |
Unmark this checkbox |
VPN Access |
Check this box |
Designated Gateway |
Unmark this checkbox |
Allocate New EIP |
Unmark this checkbox |
Enable SAML |
Unmark this checkbox |
VPN CIDR Block |
(e.g. 192.168.43.0/24) |
MFA Authentication |
Optional (Disable is fine for testing) |
Max Connections |
100 is fine for testing |
Split Tunnel Mode |
No |
Enable ELB |
Yes |
ELB Name |
Leave blank is fine for testing |
Enable Client Cert. Sharing |
No |
Enable PBR |
Check this box |
PBR Subnet |
Select the subnet where Aviatrix Peering Gateway is located (e.g. 10.1.0.0/24) |
PBR Default Gateway |
Select the private IP of Aviatrix Peering Gateway (e.g. 10.1.0.138) |
NAT Translation Logging |
Unmark this checkbox |
Enable LDAP |
Optional (Unmark this checkbox is fine for testing) |
Save Template |
Unmark this checkbox |
-
Click OK. It will take a few minutes for the gateway to deploy. Do not proceed until the gateway is deployed.
-
Create Aviatrix Peering Gateway #2 in VPC #2.
-
Click on Gateway > New Gateway.
Setting | Value |
---|---|
Cloud Type |
Choose AWS. |
Gateway Name |
This name is arbitrary (e.g. vpc-02-avx-gw) |
Account Name |
Choose the account name. |
Region |
Choose the region of VPC #2. |
VPC ID |
Choose the VPC ID of VPC #2. |
Public Subnet |
Select a public subnet where the gateway will be deployed (e.g. 10.2.0.0/24). |
Gateway Size |
t2.micro is fine for testing |
Enable NAT |
Mark this checkbox (IMPORTANT) |
VPN Access |
Unmark this checkbox |
Designated Gateway |
Unmark this checkbox |
Allocate New EIP |
Unmark this checkbox |
Save Template |
Unmark this checkbox |
-
Click OK. It will take a few minutes for the gateway to deploy. Do not proceed until the gateway is deployed.
Establishing Site to Cloud Peering Connection
This step explains how to establish a Site-to-Cloud (S2C) connection between two Aviatrix Gateways in VPC #1 and VPC #2.
Instructions:
-
From the Aviatrix Controller.
-
Click Site2Cloud > Site2Cloud.
-
Click +Add New to establish a S2C connection from Aviatrix Peering Gateway #1 (in VPC #1) to Aviatrix Peering Gateway #2 (in VPC #2).
Setting | Value |
---|---|
VPC ID/VNet Name |
Choose VPC ID of VPC #1. |
Connection Type |
Unmapped |
Connection Name |
This name is arbitrary (e.g. vpc01-s2c-vpc02). |
Remote Gateway Type |
Aviatrix (in this example) |
Tunnel Type |
UDP |
Algorithms |
Unmark this checkbox |
Encryption over DirectConnect |
Unmark this checkbox |
Enable HA |
Unmark this checkbox |
Primary Cloud Gateway |
Select Aviatrix Peering Gateway #1 in VPC #1 (e.g. vpc-01-avx-gw). |
Remote Gateway IP Address |
Public IP of Aviatrix Peering Gateway #2 in VPC #2 |
Pre-shared Key |
Optional |
Remote Subnet |
0.0.0.0/0 |
Local Subnet |
IP of eth1 of Aviatrix VPN Gateway #1 (e.g. 10.1.0.190/32) |
-
Click OK.
-
From the S2C connection table, select the Site2Cloud connection created above (e.g. vpc01-s2c-vpc02).
-
Select Aviatrix from the Vendor dropdown menu.
-
Click Download Configuration then save it.
-
Click **+Add New" to establish a Site2Cloud connection from Aviatrix Peering Gateway #2.
9. Choose VPC ID of VPC #2 from "VPC ID/VNet Name" dropdown menu. Click Import to upload. the downloaded configuration saved above. 10. This template file contains the necessary information to configure the new S2C connection.
Setting | Value |
---|---|
VPC ID/VNet Name |
Choose VPC ID of VPC #2. |
Connection Type |
Unmapped |
Connection Name |
This name is arbitrary (e.g. vpc02-s2c-vpc01) |
Remote Gateway Type |
Aviatrix |
Tunnel Type |
UDP |
Algorithms |
Mark this checkbox |
Phase 1 Authentication |
SHA-1 |
Phase 2 Authentication |
HMAC-SHA-1 |
Phase 1 DH Groups |
2 |
Phase 2 DH Groups |
2 |
Phase 1 Encryption |
AES-256 |
Phase 2 Encryption |
AES-256 |
Encryption over DirectConnect |
Unmark this checkbox |
Enable HA |
Unmark this checkbox |
Primary Cloud Gateway |
Aviatrix Peering Gateway #2 (e.g. vpc-02-avx-gw) |
Remote Gateway IP Address |
Public IP of Aviatrix Peering Gateway #1 |
Pre-shared Key |
(automatically created) |
Remote Subnet |
IP of eth1 of Aviatrix VPN Gateway #1 (e.g. 10.1.0.190/32) |
Local Subnet |
0.0.0.0/0 |
Notes: The IP of eth1 of the Aviatrix VPN Gateway can be acquired from the AWS console.
-
Click OK.
Creating an OpenVPN® User
This step explains how to create a OpenVPN® user.
Instructions:
-
From the Aviatrix Controller.
-
Click OpenVPN® > VPN Users.
-
Click button +Add New.
Setting | Value |
---|---|
VPC ID |
Choose the VPC ID of VPC #1. |
LB/Gateway Name |
Choose the ELB in VPC #1. |
User Name |
This name is arbitrary (ex. vpn-user). |
User Email |
Email address |
Profile |
Unmarking this checkbox is fine for the testing. |
-
Click OK.
-
Check your email to receive a .ovpn file.
Starting Anonymous Browsing
This step explains how to establish an OpenVPN® connection and surf the network anonymously.
Instructions:
-
Enable an OpenVPN® client tool.
-
Establish an OpenVPN® connection with the ovpn file which has received in email.
-
Confirm the connectivity to public network.
-
Ping to www.google.com.
-
Check public IP address (for example, https://www.whatismyip.com/what-is-my-public-ip-address/).
-
Check IP location (for example, https://www.iplocation.net/).
-