OpenVPN + FQDN Filter Solution
1. Solution Overview
This solution provides how to deploy a network topology to filter OpenVPN user traffic by fully qualified domain name (FQDN).
2. Configuration Workflow
2.1 Pre Configuration Checklist
Before configuring this solution, users need to make sure the following prerequisites are completed.
Pre Configuration Check List
-
Deploy the Aviatrix Controller
-
Create AWS VPC with two public subnets in a same AZ for Aviatrix OpenVPN gateway and Aviatrix Egress gateway.
These prerequisites are explained in detail below.
Deploy the Aviatrix Controller
The Aviatrix Controller must be deployed and setup prior to deploy Aviatrix Gateways. Please refer to "Aviatrix Controller Getting Started Guide for AWS" on how to deploy the Aviatrix Controller.
Check and make sure you can access the Aviatrix Controller dashboard and login with an administrator account. The default URL for the Aviatrix Controller is:
https://<public ip of Aviatrix Controller>
2.1.b Create AWS VPC with two public subnets in a same AZ for Aviatrix OpenVPN gateway and Aviatrix Egress gateway.
-
Create 1 VPC with CIDR such as 10.1.0.0/16
-
In the VPC, create 2 public subnets in a same Availability Zone such as 10.1.0.0/24 and 10.1.1.0/24. The public subnet means that it must be associated with a route table whose default route 0.0.0.0 points to IGW.
-
In the VPC, create multiple private subnets if needed.
Configuration Steps
Make sure the pre-configuration steps in the previous section are completed before proceeding.
The instructions in this section will use the following architecture. The CIDR and subnets may vary depending on your VPC setup; however, the general principals will be the same.
![image0](_images/openvpn-fqdn-filter-solution.png)
2.2.a Deploy Aviatrix Egress Gateway ------------------------------
The first step is to deploy Aviatrix Egress Gateway in the Public Subnet2 10.1.1.0/24
Instructions:
a.1. Login to the Aviatrix Controller Console
a.2. Create Aviatrix Egress Gateway in Public Subnet2 of VPC
a.3. Click on Gateway → "New Gateway"
Setting | Value |
---|---|
Cloud Type |
Choose AWS |
Gateway Name |
This name is arbitrary (e.g. egress-gw) |
Account Name |
Choose the account name |
Region |
Choose the region of VPC |
VPC ID |
Choose the VPC ID of VPC |
Public Subnet |
Select a public subnet where the gateway will be deployed (e.g. 10.1.1.0/24) |
Gateway Size |
t2.micro is fine for testing |
Enable SNAT |
Check this box (IMPORTANT) |
VPN Access |
Uncheck this box |
Designated Gateway |
Uncheck this box |
Allocate New EIP |
Check this box |
Save Template |
Uncheck this box |
a.4. Click “OK�. It will take a few minutes for the gateway to deploy. Do not proceed until the gateway is deployed.
a.5. Refer Aviatrix FQDN documents to set up Egress Filter rules and enable Egress Control function
For HA topology, see Aviatrix Single AZ HA |
2.2.b Deploy Aviatrix OpenVPN Gateway ------------------------------
The second step is to deploy Aviatrix OpenVPN Gateway in the Public Subnet1 10.1.0.0/24
Instructions:
b.1. Create Aviatrix VPN Gateway in Public Subnet1 of VPC (note that OpenVPN Gateway is in a different subnet of Egress Gateway but both are in the same AZ)
b.2. Click on Gateway → "New Gateway"
Setting | Value |
---|---|
Cloud Type |
Choose AWS |
Gateway Name |
This name is arbitrary (e.g. openvpn-gw) |
Account Name |
Choose the account name |
Region |
Choose the region of VPC |
VPC ID |
Choose the VPC ID of VPC |
Public Subnet |
Select the public subnet where the OpenVPN gateway will be deployed (e.g. 10.1.0.0/24) |
Gateway Size |
t2.micro is fine for testing. |
Enable SNAT |
Uncheck this box (IMPORTANT) |
Designated Gateway |
Uncheck this box |
Allocate New EIP |
Check this box |
VPN Access |
Check this box |
Advanced Options |
Check this box |
Enable SAML |
Uncheck this box |
VPN CIDR Block |
(e.g. 192.168.43.0/24) |
MFA Authentication |
Optional (Disable is fine for testing) |
Max Connections |
100 is fine for testing |
Split Tunnel Mode |
No (IMPORTANT) |
Enable ELB |
Yes |
ELB Name |
Leave blank is fine for testing |
Enable Client Cert. Sharing |
No |
Enable PBR |
Check this box |
PBR Subnet |
Select the subnet where Aviatrix Egress Gateway is located (e.g. 10.1.1.0/24) |
PBR Default Gateway |
Select the private IP of Aviatrix Egress Gateway (e.g. 10.1.1.185) |
NAT Translation Logging |
Uncheck this box |
Enable LDAP |
Optional (Uncheck this box is fine for testing) |
Save Template |
Uncheck this box |
b.3. Click “OK�. It will take a few minutes for the gateway to deploy. Do not proceed until the gateway is deployed.
|
2.2.c Create an OpenVPN® user
This step explains how to create a OpenVPN® user.
Instructions:
c.1. From the Aviatrix Controller Console
c.2. Click OpenVPN® → VPN Users
c.3. Click button "+Add New"
Setting | Value |
---|---|
VPC ID |
Choose the VPC ID of VPC |
LB/Gateway Name |
Choose the ELB in VPC |
User Name |
This name is arbitrary (ex. vpn-user) |
User Email |
Email address |
Profile |
Uncheck this box is fine for the testing |
c.4. Click button "OK"
c.5. Check your email to receive an ovpn file
c.6. Done
3. OpenVPN FQDN solution POC
This step proofs how this solution works.
Instructions:
-
Set up a whitelist rule with Domain Name "*.google.com", Protocol "tcp", and Port "443" in Egress FQDN Filter
-
Enable Egress filter function on Aviatrix Egress gateway
-
Enable an OpenVPN® client tool
-
Establish an OpenVPN® connection with the ovpn file which has received in email
-
Confirm that the access to www.google.com via port 443/80 works properly
5.1. Issue CLI #wget www.google.com on your host machine where you established the OpenVPN session
5.2. It should access www.google.com and download the index.html to your host machine
-
Confirm that the access to www.yahoo.com via port 443/80 does not work
6.1. Issue CLI #wget www.yahoo.com on your host machine where you established the OpenVPN session
6.2. It should not able to access www.yahoo.com
OpenVPN is a registered trademark of OpenVPN Inc.