Aviatrix Secure Edge on Customer Managed VMware ESXi and KVM Deployment Workflow

This document provides instructions for deploying an Aviatrix Edge Gateway on the customer managed VMware ESXi or an open-source Kernal-based Virtual Machine (KVM).

For an overview of Aviatrix Secure Edge, see Overview of Aviatrix Secure Edge.

Aviatrix Secure Edge Network Connectivity

The following diagram shows an example of network connectivity for Aviatrix Edge Gateway to Transit Gateway in AWS.

650

Prerequisites

Before you deploy an Aviatrix Edge Gateway on VMware ESXi or KVM, ensure the prerequisite requirements are complete, see Prerequisites for Aviatrix Secure Edge Deployment on VMware ESXi and KVM.

Aviatrix Secure Edge Deployment Workflow

To deploy Aviatrix Secure Edge, first you need to procure and onboard your edge device on the platform of your choice (see Prerequisites for Aviatrix Secure Edge Deployment on VMware ESXi and KVM). Next, you deploy the Aviatrix Edge Gateway on the edge device and attach the Edge Gateway to the Aviatrix Transit Gateway for cloud connectivity. Then, configure the Edge Gateway for LAN-side connectivity.

The diagram below provides a high-level view of the four-step process for deploying Aviatrix Secure Edge in Aviatrix Controller. You have the option to use either VMware ESXi or an open-source Kernel-based Virtual Machine (KVM) to deploy the Aviatrix Secure Edge VM and attach the ISO file. The ISO file is the equivalent of the Zero-Touch Provisioning (ZTP) token. ZTP allows to remotely deploy and provision network devices at remote locations.

600

This workflow provides the steps to create a primary and secondary (HA) Edge Gateway in VMware ESXi and KVM. It also provides the steps to attach the Edge Gateways to a Transit Gateway and connect the Edge Gateways to an external device, such as a LAN BGP router.

Creating the ZTP ISO for the Edge Gateway (Self-Managed Platform)

You must have port 443 open to the IP address of the Aviatrix Controller. For the required port access for Edge Gateway deployment, refer to Aviatrix Edge Gateway Ports and Protocols.

In Aviatrix CoPilot:

  1. Go to Cloud Fabric > Edge > Gateways tab.

  2. Click + Edge Gateway, then provide the following information.

    Parameter Description

    Name

    Name for the Edge Gateway.

    Platform

    Select edge_admin.

    Site

    Select an existing name or enter a new name to identify the edge location.

    Site names cannot contain spaces.

    ZTP File Type

    Select the ZTP file type.

    • For VMware ESXi, select iso.

    • For KVM, select iso or cloud-init.

    High Availability

    High Availability is set to Off for the primary Edge Gateway.

    For the secondary (HA) Edge Gateways, select Active-Active or Active-Standby mode.

    Deploying multiple Edge Gateways for the same site is supported. A maximum of 8 Edge Gateways are supported.

  3. Configure the WAN, LAN, and Management interfaces.

Configuring the Edge Gateway Interfaces

By default, an Aviatrix Edge Gateway has three interfaces: one WAN interface on eth0, one LAN interface on eth1, and one Management interface on eth2. You will need these configuration information to configure the interfaces.

In the Interface Configuration section, configure the WAN, LAN, and Management interfaces for the Edge Gateway.

Configuring the WAN Interface

Click WAN, then provide the following information.

For IP and DNS settings, enter using the applicable format. For example, if the Edge Gateway’s WAN IP is 10.1.1.151, enter 10.1.1.151/24 or what your netmask is.
Parameter Description

IP Assignment

The default is Static for static IP assignment.

DHCP for dynamic IP address assignment is not supported.

Interface Labels

(optional) A name to identify the WAN interface.

Interface CIDR

The CIDR for the WAN interface.

Default Gateway IP

The Default Gateway IP address for the WAN interface.

Public IP

(optional) The Public IP address of the WAN interface.

To change or update the Edge Gateway WAN connectivity to Transit Gateway, you will need to first detach the Edge-to-Transit gateway attachment, if there is an attachment.

Configuring the LAN Interface

Click LAN, then provide the following information.

Parameter Description

IP Assignment

The default is Static for static IP assignment.

DHCP for dynamic IP address assignment is not supported.

VRRP

If you have Virtual Router Redundancy Protocol (VRRP) configured for the LAN router redundancy, set this switch to On.

Interface CIDR

The CIDR for the LAN interface.

VRRP Gateway IP

The Virtual IP (VIP) address, when VRRP is enabled.

Default Gateway IP

(optional) The Default Gateway IP for the LAN interface.

Interface Labels

(optional) A name to identify the LAN interface.

VLAN Interface

If your LAN is segmented into virtual LANs (VLANs), click + VLAN Interface to add one or more VLAN sub-interfaces, then provide the following information for each VLAN sub-interface.

You cannot edit the VLAN ID after the Edge Gateway is created. To edit the VLAN sub-interface attributes, it is highly recommended to delete and recreate the VLAN sub-interface configuration.
Parameter Description

Interface CIDR

The native VLAN interface IP address.

This is the interface where the untagged packets are sent.

VRRP Gateway IP

The Virtual IP for the VRRP Gateway, when VRRP is enabled.

Default Gateway IP

The Default Gateway IP address for the native VLAN interface.

Interface Labels

(optional) A name to identify this native VLAN interface.

VLAN Sub-Interfaces

VLAN ID

The VLAN ID.

VLAN ID must be a number between 2 and 4092.

VLAN Interface CIDR

The VLAN sub-interface IP address.

VRRP Gateway IP

The Virtual IP for the VRRP Gateway, when VRRP is enabled.

Default Gateway IP

The Default Gateway IP address for this VLAN sub-interface.

Sub-Interface Tag

(optional) A name to identify this VLAN sub-interface.

Configuring the MGMT Interface

Click MGMT, then provide the following information.

Parameter Description

IP Assignment

Select DHCP or Static, depending on your environment.

This setting cannot be changed after the gateway is created.

Private Network

If the Management interface connection to the Aviatrix Controller is over a private network, set this switch to On.

Leave the setting to Off, if the connection is over the public internet.

Parameter

Description

Egress CIDR (Optional)

The CIDR range for the egress flow for the Management interface.

If a required field is missing, the interface tab is highlighted to indicate there is an error.

edge create error message

CoPilot creates the ISO file and downloads the file to your downloads folder.

Next, log in to your VMware ESXi or KVM host and upload the ISO or cloud-init file to a datastore or storage device. Then, deploy the Edge Gateway VM instance and attach the ISO or cloud-init image file to complete the Edge Gateway creation and authentication with the Aviatrix Controller.

The ISO file expires after 24 hours. You cannot download it again and will have to repeat the above steps. You must mount the ISO file to an Edge VM to complete the Edge Gateway registration within 24 hours. See Deploying the Edge Gateway Virtual Machine Instance.

Creating a Highly Available Edge Gateway (Self-Managed Platform)

  • Before you can create the highly available Edge Gateway, the primary Edge Gateway must be deployed and its status must be Up.

  • You must have port 443 open to the IP address of the Aviatrix Controller. For the required port access for Edge Gateway deployment, refer to Aviatrix Edge Gateway Ports and Protocols.

To create a secondary (HA) Edge Gateway, follow these steps.

  1. In Aviatrix CoPilot, go to Cloud Fabric > Edge > Gateways tab.

  2. In the table, locate the primary Edge Gateway for which you want to create the HA gateway and click its Edit icon.

  3. In the Edit Edge Gateway dialog box, from the High Availability dropdown menu, select Active-Active or Active-Standby mode.

  4. In the Interfaces section, configure the WAN, LAN, and Management interfaces for the secondary (HA) Edge Gateway.

    WAN Interface

    Click WAN, then provide the following information.

    For IP and DNS settings, enter using the applicable format. For example, if the Edge Gateway’s WAN IP is 10.1.1.151, enter 10.1.1.151/24 or what your netmask is.
    Parameter Description

    IP Assignment

    The default is Static for static IP assignment.

    DHCP for dynamic IP address assignment is not supported.

    Interface Labels

    (optional) A name to identify the WAN interface.

    Interface CIDR

    The CIDR for the WAN interface.

    Default Gateway IP

    The Default Gateway IP address for the WAN interface.

    Public IP

    (optional) The Public IP address of the WAN interface.

    LAN Interface

    Click LAN, then provide the following information.

    Parameter Description

    IP Assignment

    The default is Static for static IP assignment.

    DHCP for dynamic IP address assignment is not supported.

    VRRP

    If you have Virtual Router Redundancy Protocol (VRRP) configured for the LAN router redundancy, set this switch to On.

    Interface CIDR

    The CIDR for the LAN interface.

    VRRP Gateway IP

    The Virtual IP (VIP) address, when VRRP is enabled.

    Default Gateway IP

    (optional) The Default Gateway IP for the LAN interface.

    Interface Labels

    (optional) A name to identify the LAN interface.

    VLAN Interface

    Provide the following information for each VLAN sub-interface.

    Parameter Description

    Interface CIDR

    The native VLAN interface IP address.

    This is the interface where the untagged packets are sent.

    Default Gateway IP

    The Default Gateway IP address for the native VLAN interface.

    Interface Labels

    (optional) A name to identify this native VLAN interface.

    VLAN Sub-Interfaces

    VLAN Interface CIDR

    The VLAN sub-interface IP address.

    Default Gateway IP

    The Default Gateway IP address for this VLAN sub-interface.

    VLAN configurations are added to the primary Edge Gateway. On the secondary Edge Gateway, some fields are disabled and non-editable, the field value appears when it is selected.

    CoPilot creates the ISO file and downloads the file to your downloads folder.

    Next, log in to your VMware ESXi or KVM host and upload the ISO or cloud-init file to a datastore or storage device. Then, deploy the Edge Gateway VM instance and attach the ISO or cloud-init image file to complete the Edge Gateway creation and authentication with the Aviatrix Controller.

    The ISO file expires after 24 hours. You cannot download it again and will have to repeat the above steps. You must mount the ISO file to an Edge VM to complete the Edge Gateway registration within the 24-hour timeframe.

Deploying the Edge Gateway Virtual Machine Instance and Attaching the ZTP ISO

See:

Deploying the Edge Gateway Virtual Machine in VMware ESXi

To deploy the Edge Gateway virtual machine, follow these steps.

  1. If you have not downloaded the ESXi OVA file, download the file by using the link provided to you by Aviatrix Support. See Download the Aviatrix Secure Edge Image File.

  2. Log in to VMware vSphere Web client to access the ESXi host.

    You can use vSphere Web client to manage ESXi host, launch a VM, mount ISO files, and start and stop the Aviatrix Edge Gateway.

  3. Load the OVA file into the ESXi using vSphere, go to ESXi > Virtual Machines > Create/Register VM.

  4. Select Deploy a virtual machine from an OVF or OVA file and click Next.

  5. Enter a name for the Aviatrix Secure Edge VM and drag the OVA file into the blue pane, then click Next.

    edge_ova_load_file
  6. In the Select storage page, select the storage device where to create the VM instance (the OVA is installed in this instance) and click Next.

  7. In the Deployment options window, enter the Network mappings for WAN, LAN, and MGMT network interfaces and select the Deployment type. (Refer to the pull-down menu or see Virtual Machine CPU and Memory Configurations.)

    If necessary, you can change the network interface mappings after deployment.

    edge_ova_deploy_options
  8. Click Next.

  9. In the Ready to complete page, click Finish.

Next, attach the ISO file to Edge Gateway VM, which will auto-mount the media with the configuration file to be provision the Edge Gateway.

Attaching the ISO File to the Edge Gateway Virtual Machine in VMware ESXi

  • The ZTP ISO file can only be used for a single Aviatrix Secure Edge VM instance, and only one time for that instance.

  • The ZTP token expires after 24 hours. If you wait too long to boot up the VM with the attached ISO image, it will not work. In that case, delete the Edge Gateway in the Aviatrix CoPilot and create a new Edge Gateway to receive a new ISO file.

  1. Upload the ISO file downloaded from Aviatrix CoPilot to your VMware datastore.

  2. In vSphere, select the Aviatrix Secure Edge VM you created and click Edit settings.

  3. Select the Virtual Hardware tab.

  4. Next to CD/DVD Drive 1, click the dropdown menu and select Datastore ISO file.

  5. Next to CD/DVD Drive 1, ensure the Connect box is checked and click Save.

    Connect at power on is required when you attach the ISO image to the VM for the first time. If the VM is powered on at the time you attach the ISO image, select the ISO file and save the configuration to make the ISO available to ZTP.

  6. Next to the CD/DVD Media, click Browse, locate the datastore and select the ISO file you uploaded.

    edge_edit_settings
  7. Click Save. ZTP auto-mounts the ISO file and deploys the Edge Gateway on the VM.

  8. Verify the Edge Gateway is Up (see Verifying the Edge Gateway Creation).

Deploying the Edge Gateway Virtual Machine in KVM

Before you begin, on the KVM Linux host ensure the LAN, WAN, and MGMT network bridges are associated with the physical ethernet interfaces on the KVM sever. Refer to KVM product documentation.

KVM Hypervisor does not support configuration of RX/TX queue size during runtime. RX/TX queue size should be configured during Edge Gateway VM bootup. See Enabling Multiqueue virtio-net on KVM.

  1. If you have not downloaded the KVM QCOW2 file, download the file by using the link provided to you by Aviatrix Support. See Download the Aviatrix Secure Edge Image File.

  2. Launch Virtual Machine Manager UI to access the KVM host.

  3. Create a new virtual machine from an existing disk image.

    1. From the File menu, select New virtual machine.

    2. Select the option Import existing disk image.

    3. Click Forward.

      edge-kvm-new-vm
  4. Provide the path to the KVM QCOW2 file and specify the operating system type and version.

    1. Enter the path or use the Browse button to locate the KVM QCOW2 file you previously downloaded.

    2. For OS type, select Linux.

    3. For Version, select Ubuntu 18.04 LTS.

    4. Click Forward.

      edge-kvm-new-vm-2
  5. Enter the memory and CPU settings for the Edge Gateway VM and click Forward.

    edge-kvm-new-vm-3
  6. Enter a name for the Edge Gateway VM and check the Customize configuration before install checkbox, then click Finish.

    edge-kvm-new-vm-4
  7. Add the LAN and MGMT virtual bridge interfaces.

    1. Click Add Hardware.

      edge-kvm-new-vm-5
    2. In Add New Virtual Hardware, select Network from the left pane and add two additional network interfaces for the LAN and MGMT virtual bridges. The virtual bridge for the WAN interface is automatically added as part of the VM image creation.

    3. For Network source, select the name of the virtual bridge for the LAN interface.

    4. For Device model, select virtio.

    5. Repeat steps a and b and add the virtual bridge for the MGMT interface.

      edge-kvm-new-vm-6
  8. Choose the storage device and attach the ISO file to the VM.

    1. In Add New Virtual Hardware, select Storage from the left pane.

    2. Select the option Select or create custom storage.

    3. Click Manage.

    4. Locate and select the KVM iso file which you previously uploaded.

    5. Click Choose Volume.

    6. Click Finish.

      edge-kvm-new-vm-7
  9. Click Begin Installation to create the Edge Gateway VM on the KVM host.

    After the VM is created, ZTP auto-mounts the ISO file and deploys the Edge Gateway on the VM.

  10. Verify the Edge Gateway is Up (see Verifying the Edge Gateway Creation).

Attaching the Edge Gateway to the Transit Gateway

Prerequisites

Before you attach the Edge Gateway to the Transit Gateway, perform these prerequisite steps.

  1. Ensure Local ASN Number is configured on Edge and Transit Gateway.

  2. If the Edge to Transit Gateway attachment is over public network, you need to update the WAN Public IP on the Edge Gateway.

    1. Go to Cloud Fabric > Edge > Gateways tab.

    2. Locate the Edge Gateway, and click its Edit icon on the right.

    3. In Edit Edge Gateway, scroll to the Interfaces section and click WAN.

    4. In Public IP, click Discover.

      edge discover public ip
    5. Verify the WAN Public IP and click Save.

Attach Edge Gateway to Transit Gateway

You can attach an Edge Gateway to multiple Transit Gateways. Each attachment can be configured with different parameters, such as connecting interfaces, connection over private or public network, high-performance encryption, and Jumbo Frame.

  • To create a High Performance Encryption mode attachment, make sure the Transit Gateway is created with High Performance Encryption enabled.

  • If you want Jumbo Frame enabled on the Edge Gateway, make sure to enable Jumbo Frame on the Edge Gateway before you attach it to the Transit Gateway.

In Aviatrix CoPilot:

  1. Go to Cloud Fabric > Edge > Gateways tab.

  2. Locate the Edge Gateway, click the three-dot vertical menu on the right, and select Manage Transit Gateway Attachment.

    edge-attach-edge-to-transit

    Click + Transit Gateway Attachment, then provide the following information.

    Parameter Description

    Transit Gateway

    From the dropdown menu, select the Transit Gateway to attach to the Edge Gateway.

    Connecting Edge Interfaces

    From the dropdown menu, select the WAN interface connection to the Transit Gateway.

    In the Advanced section, set the advanced gateway settings that apply.

    Parameter Description

    Attach over Private Network

    If the Edge WAN connection to the Transit Gateway is over a private network, set this toggle to On.

    Leave it Off if the connection is over the public internet.

    Jumbo Frame

    If you want to use Jumbo Frames for the Transit-to-Edge Gateway connection, set this toggle to On.

    High Performance Encryption

    If you want to enable high-performance encryption for the Transit-to-Edge Gateway connection, set this toggle to On.

    In Number of Tunnels, enter the number of HPE tunnels to create.

    • For HPE over private network, setting the number of tunnels count to 0 creates maximum tunnels based on the peering gateway size.

    • For HPE over public network, the number of tunnels count supported range is between 2 and 20.

    To attach the Edge Gateway to another Transit Gateway, click + Transit Gateway Attachment again and provide the required information.

  3. Click Save.

Connecting the Edge Gateway to an External Device (BGP over LAN)

To connect the Edge Gateway to the LAN router using BGP over LAN, follow these steps.

  1. Navigate to Networking > Connectivity > External Connections (S2C) tab.

  2. Click + External Connection, then provide the following information.

    Parameter Description

    Name

    Name to identify the connection to the LAN router.

    Connect Local Gateway To

    Select External Device radio button, then from the dropdown menu, select BGP over LAN.

    Local Gateway

    The Edge Gateway to connect to the LAN router.

    Local ASN

    The Local AS number the Edge Gateway will use to exchange routes with the LAN router.

    This is automatically populated if the Edge Gateway is assigned an ASN already.

    Remote ASN

    The BGP AS number configured on the LAN router.

  3. Click + Connection and provide the following information.

    Parameter Description

    Remote LAN IP

    The IP address for the LAN router.

    Local LAN IP

    This is automatically populated with the Edge Gateway LAN interface IP address.

    edge external connection
  4. Click Save.

Enabling Multiqueue virtio-net on KVM

Multiqueue virtio-net allows network performance to scale with the number of vCPUs, by allowing packet processing (packet sending and receiving) through multiple TX and RX queues.

To enable Multiqueue virtio-net support on KVM, when launching the Edge Gateway VM using virt-install, add the driver_queues parameter to the network interface details.

--network bridge=<bridge-name>, model=virtio,driver_queues=N

where N is the number of vCPUs.